How to Get Sticker Residue Off Car

Posted on

How to Get Sticker Residue Off Car

Most of the drivers who possess their own car end up at some point putting a sticker on it. Some put in the tin, others put it in the glass. Some place small and discreet adhesives somewhere in the vehicle, while others cannot see an empty space in their vehicle. Regardless of the motive and type of adhesive, it will come a moment that people will feel the need to take them out, either because the person intends to sell the car, ie because of they simply tired of them.

How to Get Sticker Residue Off Car

But also drivers don’t take too long to find out that the task of removing a sticker from the car can be much harder than putting it. It is very common that people remove them, end up leaving behind some pieces of their own adhesives, besides the glue that ends up sticking to the car. Even some pieces of paint can leave when people try to take the stickers off. The good news is that there are some methods that can help people at the time of removing them. Let’s check out some of them.

Methods with Oakum

To remove an adhesive safely, trying to cause the lowest possible damage in the automobile, it is important to have a burlap cloth nearby; He will be extremely helpful. We will pass a method that can be followed using this material:

First start removing the plastic or paper from the adhesive with your hands, trying to take as much as possible without using any other type of material. After that, take advantage that you have your burlap cloth around and soak it with a little kerosene. Now rub the cloth over the glue remaining of the adhesive in the car. Movements should not be very aggressive and can be made in a circular motion, to loosen this glue more easily. To the extent that the person is doing this she will realize that the cloth is getting too much glue, so it is important to take another unit and soak it with a little more kerosene and keep rubbing.

If the person is attempting to eliminate an adhesive that is glued to the car’s glass, after removing the glue correctly, it will be necessary to take a newspaper sheet, smash it and rub it in the glass, to completely remove the oiliness that was from kerosene, and it is possible that the person use some specific product to clean glass together with the newspaper.

If it is in the tin, the recommended is to pass a bit of automotive wax on the spot with the finger and then a clean cloth of oakum in circular movements, to standardize the wax. After removing it completely, it is recommended that the person passes once again a clean burlap cloth and also a dry flannel on site.

Hair-Dryer method

In all methods, it is necessary that the person can start removing the adhesive, but some end up gluing so well in the car that people can even touch them. That’s why at this point people need to find some alternatives to loosen the stickers a bit and so make it easier, to pull with the hands. In this case, something that can help a lot is a hair dryer or even a hot air pistol, which can be rented in some household cleaning segment houses.

It’s important that the dryer or the pistol be potent. To start removing the adhesive this way, people should place one of the auxiliaries quoted above at least 15 centimeters and leave it plugged into the maximum power and the hotter air between one and two minutes. Move the dryer through the entire extension of the adhesive and leave it a time against the corners, which can be lifted. That’s because the wind strength combined with the heat of the air will make the glue the adhesive, the weaker, and in this way, these corners begin to rise.

Once the corners start lifting, people can start trying to pull the adhesive with their hands. It is also possible that the person uses a shaving blade to help remove the adhesives, but in this case, it is important that people be very careful not to scratch the car so that the paint is damaged. Slowly pull back, in the opposite direction, not up. Continue to apply heat as needed. After removing the adhesive, remove the residues with an automotive remover, such as the PPG Ditzo DX 440. You may have to reapply wax in that area.

Adhesives on the glass may be more complicated to withdraw.

 

Lubricant method

If the adhesive is too glued, but still possess some unglued tip, people can use the lubricant to get the adhesive off without leaving many spots and pieces behind. For this, start by removing the corners that are looser, and go applying spray lubricant in this corner. It is recommended that the person uses WD-40 or Triflow, in order to achieve a more efficient result in the removal of the adhesive.

As the person is placing the lubricant, the trend is that the glue that is impregnated with the adhesive and the car will dissolve, thereby facilitating the removal of the adhesive. Go pull the adhesive on the corner and when it gets more trapped, apply more lubricant.

Do not forget that after the adhesive is removed it will be necessary to perform a good cleaning on the site, so that all the rest of the glue and the lubricant, come out.

Please rate this

One thought on “How to Get Sticker Residue Off Car

Leave a Reply

Your email address will not be published. Required fields are marked *

*